Possible causes include:
1. Poor installation (misaligned casing, head/tail sprockets not centered, improper bearing installation) → Inspect and correct installation.
2. Deformation of the conveyor trough → Repair or straighten the casing.
3. Improper tensioning causing tail sprocket misalignment → Adjust the tensioning device evenly.
1. Poor installation (misaligned casing, head/tail sprockets not centered, improper bearing installation) → Inspect and correct installation.
2. Deformation of the conveyor trough → Repair or straighten the casing.
3. Improper tensioning causing tail sprocket misalignment → Adjust the tensioning device evenly.
1. Insufficient strength → Verify and upgrade chain strength.
2. Foreign objects jamming the chain → Remove debris.
3. Chain wear → Replace the chain.
4. Overloading → Ensure even material feeding.
2. Foreign objects jamming the chain → Remove debris.
3. Chain wear → Replace the chain.
4. Overloading → Ensure even material feeding.
1. Misaligned head sprocket → Adjust alignment.
2. Improper installation of the conveyor trough → Inspect and correct.
3. Chain pitch elongation → Replace the chain.
4. Worn sprocket teeth → Repair or replace.
2. Improper installation of the conveyor trough → Inspect and correct.
3. Chain pitch elongation → Replace the chain.
4. Worn sprocket teeth → Repair or replace.
1. Low motor speed → Check and adjust motor system.
2. Uneven feeding → Regulate material flow.
3. Dust buildup in bearings → Clean or replace bearings and lubricate.
4. Incorrect bucket type → Select appropriate bucket design.
2. Uneven feeding → Regulate material flow.
3. Dust buildup in bearings → Clean or replace bearings and lubricate.
4. Incorrect bucket type → Select appropriate bucket design.
1. Low motor speed → Check and adjust motor system.
2. Uneven feeding → Regulate material flow.
3. Dust buildup in bearings → Clean or replace bearings and lubricate.
4. Incorrect bucket type → Select appropriate bucket design.
2. Uneven feeding → Regulate material flow.
3. Dust buildup in bearings → Clean or replace bearings and lubricate.
4. Incorrect bucket type → Select appropriate bucket design.
1. Drive and idle rollers not parallel → Adjust alignment.
2. Improper belt joint → Reconnect the belt properly.
3. Uneven frame installation → Adjust the frame.
4. Misaligned rollers → Adjust roller brackets along belt direction.
2. Improper belt joint → Reconnect the belt properly.
3. Uneven frame installation → Adjust the frame.
4. Misaligned rollers → Adjust roller brackets along belt direction.
1. Belt speed too fast or too slow → Adjust shaft speed.
2. Improper gap between discharge chute and buckets → Adjust clearance.
3. Blocked discharge outlet → Clear the outlet.
2. Improper gap between discharge chute and buckets → Adjust clearance.
3. Blocked discharge outlet → Clear the outlet.
1. Drive and idle rollers not parallel → Adjust alignment.
2. Improper belt joint → Reconnect the belt properly.
3. Uneven frame installation → Adjust the frame.
4. Misaligned rollers → Adjust roller brackets along belt direction.
2. Improper belt joint → Reconnect the belt properly.
3. Uneven frame installation → Adjust the frame.
4. Misaligned rollers → Adjust roller brackets along belt direction.
1. Insufficient belt tension → Tighten using tensioning device.
2. Smooth drum surface → Add rubber lagging.
3. Overloading → Reduce load.
4. Faulty drum bearings → Clean or replace bearings.
2. Smooth drum surface → Add rubber lagging.
3. Overloading → Reduce load.
4. Faulty drum bearings → Clean or replace bearings.
1. Belt not contacting rollers → Adjust roller position.
2. Lack of lubrication or damaged bearings → Repair or replace bearings.
2. Lack of lubrication or damaged bearings → Repair or replace bearings.
1. Blade rubbing against casing → Adjust or replace the central shaft.
2. Damaged bearing housing → Replace bearing housing.
3. Damaged hanger → Replace hanger.
2. Damaged bearing housing → Replace bearing housing.
3. Damaged hanger → Replace hanger.
1. Shaft deformation → Repair or replace shaft.
2. Damaged bearing housing → Replace bearing housing.
3. Damaged hanger → Replace hanger.
2. Damaged bearing housing → Replace bearing housing.
3. Damaged hanger → Replace hanger.
The main cause is blade wear or excessive clearance between the blade and casing.
→ Replace worn blades or the screw assembly.
→ Replace worn blades or the screw assembly.
If you have any questions during operation, feel free to contact us.
We are committed to providing professional solutions and reliable support
We are committed to providing professional solutions and reliable support